Ansel VS211 Manuel d'utilisateur

VS211 1 FXS / 1 FXO VoIP Telephone Adaptor User Manual V1.1p

Phone Book 8.6. The Phone Book page specifies Speed Dial and Hot Line function. Speed Dial Settings 8.7. For Speed Dial function you can add/delete

Hot Line Setting 8.12. The Hot Line mode allows to making a direct call at the IP stored in the page without dialing. Hot-Line Mode is very conve

Call Settings 8.16. The subpages are as follows; Call Forward, SNTP, Volume, Block Settings, Auto Answer, Caller ID, Dial Plan, Flash Ti

SNTP Setting: 8.19. You can setup the primary and second SNTP Server IP Address, to get the date/time information. You may also

Block Setting: 8.21. You can setup the Block Setting to keep the phone silence. You can choose either Always Block or a Block period. 8.22. Alwa

Auto Answer Setting: 8.25. You may enable the Auto Answer function to answer the incoming call by VS211 FXO port. When the ring count exceeds the

Caller ID Setting: 8.26. You may show caller ID in your PSTN Phone or IP Phone by selecting “Yes” in Single Caller ID, and the desired Caller ID op

Dial Plan Settings: 8.27. The dial plan allows you to map the dialing into an easy-to-remember phone number system. When replace prefix code is

Flash Time Setting: 8.38. You can set the flash time duration for the telephone flash key or hook switch in this page. The telephone flash ke

Call Waiting Setting: 8.39. You can enable the call waiting function in this page. It allows answering another coming call by pressing flash ke

Quick Guide Step 1: Broadband (ADSL/Cable Modem) Connections for VS211 A. Connect VS211 WAN port to ADSL NAT Router as the following connection. B.

T.38 (FAX) Setting: 8.40. T.38 function can be used for FAX transmission over IP. Note that T.38 function must be enabled for both side o

Network 8.41. VS211 is equipped with an embedded NAT router between WAN and LAN ports to meet the IP Network requirements. If you have an externa

WAN Settings: 8.43. The WAN setting is used to configure the Ethernet port connects to the ADSL Modem/Router. 8.44. The default setting is for NA

LAN Settings: 8.49. The default IP address is 192.168.123.1, with Net Mask 255.255.255.0., and DHCP Server enabled. The IP addresses for DHCP are

DDNS Setting: 8.52. You need to have a DDNS account before configuring the DDNS setting. Usually, most of the VoIP applications are working with a

8.58. CFI: Canonical Format Indicator is always set to zero for Ethernet switches. CFI is used for compatibility between Ethernet type network

SIP Settings 8.61. You can setup the Service Domain, Port Settngs, Codec Settings, RTP Setting, RPort Setting and Other Settings for SIP Proxy Server

23

Codec Settings: 8.78. You can setup the Codec priority, RTP packet length, and VAD function in this page. You need to follow the ITSP

Codec ID Settings: 8.79. You can setup the Codec ID in this page. You need to follow the ITSP suggestion to setup these items. Other Setting

E. You need to set up the following web configurations: Network Settings, SIP Settings, NAT Settings/STUN Settings. Remember to submit, save a

Auto Configuration Setting 8.81. Auto Configuration function can be used to download the original configurations stored in the TFTP, HTTP or FTP s

27

User Password 8.82. You may change the login name and password in this page. Save Changes 8.83. You can save the changes you have made

Update 8.84. VS211 provides two methods, HTTP or TFTP, to update new firmware as the following steps: 8.85. Select the firmware code type, Risc or

8.88. After clicking the “Update” button, the firmware list will be displayed from server to indicate the available firmware for download. 8.89. Sele

Default Setting: 8.93. You can restore the VS211 to factory default in this page. By clicking the “Restore” button, the VS211 will restore to

Reboot 8.94. You may click the Reboot button to restart, then VS211 will automatically reboot with the stored configurations.

9. Configurations by Telephone & IVR You can use telephone to configure and to check the status of VS211. Make sure that the LAN port is con

Group IVR Action Phone Command Remarks Setting Enable Call Waiting #138# This will disable Call Transfer. Setting Disable Call Waiting #139# Th

10. VoIP Application Examples You can use PC Web browser to configure VS211. For example, enter http://192.168.123.1 from PC web browser. A. A

TABLE OF CONTENTS 1. Introductions……………………………………………………………… 2. Features ……………………………………………………………………… 3. Standard Compliances…………………………………………… 4. Packi

Example 1: Public Switched Telephone Network (PSTN) Calling/Answering Applications: VS211 is default at the VoIP mode. For PSTN calls, you may

Callings: 8. Pick up the phone, and you should hear a dial tone for VoIP mode. 9. Press 1688# or 1688 to call the party with the registered SIP phon

Example 4: SIP to Direct IP Calling Applications: The application is for the calling party with ADSL connection as in either Diagrams A or B.

Example 6: Direct IP to Direct IP Calling/Answering Applications: The applications are for ADSL connection without NAT router as in Diagram A.

Example 8: Direct IP to PSTN Calling Applications: The Direct IP to PSTN calling is for the application when the answering parties

Example 10: 3-Way Conference Call, Call Waiting, Call Hold 3-Way Conference Calling Application: This is for 3-way conference call among Part

Example 11: SIP-to-SIP Calling for FreeWorld Dialup (FWD) Applications: This shows how to use FWD as an example for free ITSP provider. The

43

5. SIP Settings You have to enter the Display Name, User Name, Registered Name, Registered Password, Domain Server (fwd.pulver.com), Proxy Ser

Callings: 6. Pick up the phone for VoIP mode. (Your FWD phone number 636346). 7. Press 654321 to call the party with the registered F

1. Introductions The VS211 is a 1-port FXS / 1-port FXO Telephone Adaptor (TA) with SIP Protocols for Voice over IP (VoIP) applications. Connec

11. Trouble Shooting for Web Configurations 11.1. DO NOT HEAR DIAL TONE? The phone port of VS211 is set to VoIP mode at default. When you pick u

11.3. ONLY ONE IP AVAILABLE FROM ADSL/CABLE SERVICE PROVIDER? Sometimes only one IP address is available from Internet Service Provider (ISP) withou

11.4. VOIP EXTENSION CALLS TO PSTN ARE NOT WORKING? You must enable the Auto Answer function in Call Settings in order to answer automatically by Vo

3. Standard Compliances The VS211 VoIP TA supports for the following standards VoIP Protocol: IETF RFC3261 and RFC 2543 for SIP SIP Authentica

6. Installations & SIP Configurations 1. Connect VS211 RJ45 WAN port to NAT Router using a Category 5 LAN cable. 2. Connect VS211 RJ45 L

8. Configurations by Web Browser You may enter the IP address from PC Web browser to configure VS211. For example, enter http://192.168.123.1 f

System Information 8.4. You will see the system information such as firmware version, Codec, etc in this page. 8.5. You may click the button list a